LOG PROFILES
Square Logs
Milled Logs
Decks/Roofs/Fences
CARE PRODUCTS
Application Tools
Chinking
Cleaners
Exterior Finishes
Exterior Top Coat
Interior Finishes
Interior Urethanes
Preservatives
Sealants
All Products
MANUFACTURERS
Perma-Chink
Sashco
SaverSystems
Sikkens
CARE TIPS
Maintenance
Insects
Clean Logs
Apply Stain
Caulk & Chinking
Checklists
RESTORATION
Q&A
Checklist
Staining
Chinking
Corn Blasting
Free Estimate
ORDERING
Information
Free Freight
View Shopping Cart
Order Check Out
About Us
Contact Us
Log Home Links
Toll Free:
1-800-726-0708
Site is Sponsored By
Fine Traditional Log Homes since 1980
|
DESCRIPTION |
DESCRIPTION:
DEFY is a high performance, water based
wood finish formulated to prevent the damaging effects of water,
fungi, and UV radiation on exterior wood. It is a V.O.C. compliant
blend of natural and synthetic resins which penetrates wood pores
to block out water and provide long-lasting protection from weather
damage. The product's excellent penetration helps eliminate surface
build-up and peeling, making future maintenance coats easier
to apply. A unique feature of DEFY is that it contains nutrient-free
resins, instead of high levels of fungicides, to prevent mold
and mildew growth. DEFY protects wood from warping, checking,
swelling, cupping and damage from wet/dry cycles. |
USES |
BENEFITS |
DIRECTIONS
FOR USE |
APPLICATION |
HELPFUL
HINTS |
HEALTH
AND SAFETY |
LIMITED
WARRANTY |
AVAILABILITY
AND COST |
MAINTENANCE |
TECHNICAL
DATA |
USES:
DEFY can be used
on interior or exterior wood surfaces including: wood siding,
log homes, decks, fences, shake shingles, outdoor wood funiture,
pressure-treated and all other natural wood surfaces. DEFY is
available in clear, as well as a wide range of transparent finishes.
Clear will allow wood to age to a silver or light gray color. |
BENEFITS:
* Waterproofs
* Superior UV resistance
* Mold and mildew resistant
* Will not flake or peel
* Soap and water clean up
* Easy to maintain |
DIRECTIONS
FOR USE:
Surface preparation
for new and aged woods: Wood surfaces must be clean and porous.
Use Saver Systems' wood cleaner/brightener, TimberWash TM, to
remove mill glaze, dirt, mildew, graying, previous coatings,
or other foreign matter that might block surface pores and interfere
with product penetration. Rinse thoroughly with power washer
(minimum 1500 p.s.i.) and allow to dry 12-24 hours. Drying time
will vary with environmental conditions. For dense woods like
cedar, light sanding before application may be necessary to ensure
proper penetration. Note: For cleaning redwood: TimberWash will
darken redwood. Use Saver Systems concentrated brightener TimberBrite
to clean and restore redwood. Check wood porosity: sprinkle a
few drops of water on wood to be treated. If the water penetrates
within 1-2 seconds the wood is ready to be treated. If not, allow
wood to dry longer and retest. Weather conditions: surface and
air temperatures should be between 45 and 95 degrees farenheit.
Avoid application in direct sunlight. Apply product to southern
exposed areas during coolest part of the day. Surface may be
slightly damp, but not wet or water saturated. Do not apply when
rainfall is expected within 12 hours unless protected with a
polyethylene film or its equivalent. |
APPLICATION:
Test a small area before starting general application to assure
desired results and coverage rates. Do not use on painted or
varnished surfaces. Stir thoroughly before using. Do not thin
product. Provide adequate ventilation. Shake or stir contents
before, and periodically during, use. To ensure absolute color
uniformity from container to container, mix at least 1/3 of the
product from a used container with the contents of a new one.
Use plastic, cardboard and/or drop clothes to protect all
adjacent non-targeted surfaces such as siding, windows, masonry,
plant life etc. from overspray and runoff.
Methods of Application:
Brush: Use a good quality nylon or polyester brush.
Roller: Use a synthetic roller with 1/2 inch to 3/4 inch
nap depending on wood texture. Backbrush to ensure penetration.
Sponge pad applicators: sponge pads are excellent for
finishing decks and smooth wood surfaces. Do not use on rough
wood.
Spray: use lowest pressure that achieves a uniform spray
pattern to minimuze fogging and overspray. For airless sprayers
use tips between .011 and .018. A Saver Systems sprayer/applicator
or other pump-up sprayer may also be used. Always backbrush
to ensure a uniform application.
General Application:
Saturate wood with two wet-on-wet coats for maximum protection.
Apply first coat and brush or backroll product into surface working
out all drips, puddles, or areas of overspray before product
dries. Use the same method to apply a second coat within 5-10
minutes, or as soon as possible. Do not allow drying between
coats. To avoid lap marks, do not stop in the middle of boards,
logs, or sections. Note: Complete entire sections or to
a natural break before allowing to dry. Since the end grain of
wood is more absorbent, it is important to throughly coat the
ends of boards or logs to prevent water penetration. All surface
checks on logs should be thoroughly coated.
Vertical Surfaces: Start from the bottom and work up.
Treat the entire length of a board before moving up. If necessary,
brush or feather in to avoid lap marks. Brush or roll in product
before it dries and work out all drips, runs, or overspray.
Decks: Remove all furniture, grills, planters, etc. Start
by applying DEFY to the outside of railings, benches, and undersides
of upper level decks (only one coat is required on undersides).
Once underside is treted, immediately brush out all overspray,
drips, etc. on top deck. Treat horizontal surfaces last. Proceed
with general application.
Wood Shingles: Clean and test for porosity. Apply 2 heavy
saturation coats, wet on wet. Backroll, or brush between coats
to ensure a uniform application. Make sure all drips and puddles
are brushed out. To avoid lap marks, start at the bottom and
treat entire length of roof before moving up. Recoat is necessary
when wood starts to turn light gray in color. |
HELPFUL
HINTS:
Because DEFY forms a
long-lasting bond with all surfaces, it is important to remove
overspray from non-targeted areas immediately with soap and water.
Overspray that is allowed to dry may be difficult or impossible
to remove. If allowed to dry, product cannot be removed from
concrete and masonry.
Dry time:
to touch; 2 to 6 hours depending on temperature and humidity.
Allow 24 hours for decks to dry before using.
Clean up: clean tools and equipment immediately
after use with soap and water. Remove overspray or spillage immediately
with soap and water.
Coverage: with two wet-on-wet coats, one gallon
of DEFY will cover approximately 150-300 sq. ft. per gallon,
depending on wood texture and porosity. |
HEALTH AND
SAFETY
Avoid contact with
eyes, skin, and clothing. May cause skin irritation. Avoid breathing
vapors or mists which may be irritating or harmful if inhaled.
Use only with adequate ventilation. For additional information,
consult the Material Safety Data Sheet.
Caution: Accumulation of product on ladders, scaffolding,
decks, etc. may result in a slippery surface. |
LIMITED
WARRANTY
Our recommendations
for use of this product are based upon tests believed to be reliable.
Since field conditions vary widely, the user must determine the
suitability of the product for the particular use and specific
method(s) of application. Due to the fact that Saver Systems has
no control over surface preparation and application methods,
no guarantee as to results is offered, expressed, or implied.
Saver Systems only warrants the contents of the container. If
the product is defective, a refund of the material cost or replacement
material will be provided at the manufacturer's option. Labor
costs are not covered by this warranty. Responsibility for claims
of any kind are strictly limited to the purchase price of the
material. |
AVAILABILITY
AND COST
DEFY is available
from distributors and dealers throughout North America. "In
place" cost of DEFY will vary with project conditions and
regional considerations. Specific job costs may be obtained from
any Saver Systems distributor or dealer.
Packaging: Packaged in 1 and 5 Gallons recyclable plastic
containers.
Transport and storage: DEFY is not considered hazardous
under Depart of Transportation regulations. Do not stack pallets.
Keep product from freezing. |
MAINTENANCE:
Remove all substances
which might stain or hold moisture on treated surfaces as quickly
as possible to minimuze damage. Occasional cleaning with mild
detergent and water will generally restore treated surfaces to
their original appearance. For maximum protection, a light maintenance
coat is recommended on horizontal surfaces every 12-24 months
depending on foot traffic and environmental conditions. Vertical
surfaces should be retreated every 3-5 years, before wood starts
graying. |
TECHNICAL
DATA:
Test Results:
ASTM D5401: Per cent water absorption on wood treated
with DEFY:<1%.
ASTM G53: Accelerated weathering (QUV) 2,500 hrs. Excellent
color retention; no loss in water repellency.
Outdoor Exposure: Indiana and Texas test fences; 2 years.
Excellent color retention, no loss in water repellency. |
|
Top of page! |
|